the nslookup works. That involves a different server. However, since you have an IP address that way try using it in a tracert. That way, you will be testing both ICMP (the protocol involved with a PING) and DNS because eventually tracert may decide to start showing you some address names when it does a reverse lookup for the other addresses which would be involved in the PING.

Nov 16, 2011 · and make ipv6 the best ping response ,try ping -4 to get ipv4 address. u have to see what make it active. The Teredo component is enabled but inactive by default. In order to become active, u must either install an application that needs to use Teredo, or configure the advanced settings on a Windows Firewall exception to use edge traversal. Dec 21, 2018 · A common response is usually to simply disable Windows Firewall entirely, however this is not recommended as the Windows Firewall does a good job at providing a basic level of system protection. We will only be allowing the specific rules required to allow ping to succeed. Allow ping through Windows Firewall I think your ping is not working because of SELinux. Try the following command as root: $ system-config-securitylevel-tui Change the Security Level to disable and change the SELinux to disable also. Now try to ping, I think now it shud work if there is no network problem. If the address 192.168.1.254 belongs to the aforementioned router, the issue is quite clear - the router is answering with ip no resources - your host has nothing to do with it. You could run another ping to a host behind the router to see if the ip no resources response would come up occasionally as well. – the-wabbit Dec 14 '11 at 16:42 I assume there have been updates since then to ClearOS and BackupPC because when starting BackupPC again, today, the backup of all Windows machines fails with the message 'no ping response'. No changes where made to the BackupPC configuration. Current version of ClearOS is 7.2.0 (Final) and BackupPC.x86-64 3.3.1-5.el7 Method: rsyncd -----Original Message----- From: address@hidden [mailto:address@hidden On Behalf Of UV Sent: ד 10 יולי 2013 09:53 To: address@hidden Subject: [lwip-users] No Ping Response Hi I'm using lwIP 1.4.1 on STM32F207. For some reason I cannot ping the device from my PC. I've modified icmp.c based on the bug# 38803 and it still does not work. Jul 26, 2019 · In email outreach, expecting a response from the initial email without following up with the prospect is the biggest rookie mistake a marketer or salesperson can make. At Sumo, our growth team reaches out to book a meeting with a prospect. We then send five or six follow-up emails to in the case of no response.

This sort of ping command will most often result in one of two responses. You will either see something like this (which is a good response): 72 bytes from 64.207.129.35 time = 12.2 ms 72 bytes from 64.207.129.35 time = 12.2 ms 72 bytes from 64.207.129.35 time = 12.2 ms 72 bytes from 64.207.129.35

In cases of no response from the target host, most implementations display either nothing or periodically print notifications about timing out. Possible ping results indicating a problem include the following: H,!N or !P – host, network or protocol unreachable; S – source route failed; F – fragmentation needed To ping the destination 10.0.99.221 and resolve 10.0.99.221 to its host name, type: ping /a 10.0.99.221 To ping the destination 10.0.99.221 with 10 echo Request messages, each of which has a Data field of 1000 bytes, type: ping /n 10 /l 1000 10.0.99.221 To ping the destination 10.0.99.221 and record the route for 4 hops, type: ping /r 4 10.0.99.221

I needed to move my ESX Host Server to another rack, brought it down, moved the rails, plugged a extra NIC Card into the PCIExpress Slot, brought the

-----Original Message----- From: address@hidden [mailto:address@hidden On Behalf Of UV Sent: ד 10 יולי 2013 09:53 To: address@hidden Subject: [lwip-users] No Ping Response Hi I'm using lwIP 1.4.1 on STM32F207. For some reason I cannot ping the device from my PC. I've modified icmp.c based on the bug# 38803 and it still does not work. Jul 26, 2019 · In email outreach, expecting a response from the initial email without following up with the prospect is the biggest rookie mistake a marketer or salesperson can make. At Sumo, our growth team reaches out to book a meeting with a prospect. We then send five or six follow-up emails to in the case of no response. the nslookup works. That involves a different server. However, since you have an IP address that way try using it in a tracert. That way, you will be testing both ICMP (the protocol involved with a PING) and DNS because eventually tracert may decide to start showing you some address names when it does a reverse lookup for the other addresses which would be involved in the PING. This is a /29 subnet, so it starts at 172.18.175.137 and ends at 172.18.175.143. Is the host you are trying to ping in that range ? Is your destination host able to use tagged frames (only port in this vlan is port 6 tagged). Dec 04, 2013 · a) I can ping another machine from the R2 server but the other machine cannot ping R2 server. b) When I reboot the other machine though then ping can access the R2 server. c) The R2 is joined to the domain and I'm using it just to host some VMs. Feb 20, 2019 · After disconnecting the VPN there is no way to communicate with a resource on the network or Internet whatsoever. Disconnecting, disabling or resetting the WiFi adapter will not work. Also restarting several network related services will not fix this issue. When pinging, for example, google.com results in: No resources. If the ping response time is less than 1ms, the management switch should’ve been recovered (No action is required). Only if it is more than or equal to 1ms, we’d better to restart the management switch à Go to step 3) [Example] In this example, avg. response time is 0.234. So no action required. [nasadmin@vnx5300-1 ~]$ ping-c 5 128.221.252.50